96gsx's 1996 Misubishi GSX

[96gsx]

Evo316g
Ported 2g exhasut manifold
Ported 2g o2 housing
3in turbbo back exhaust
Dejon 3in drawthrough intake
6in K&N filter
MBC

Dsmlink V2.5
MAFT V2.01
3in MAF (blowtrhough)
3.3bar GM MAP sensor
PLXM300 wideband (rear o2 location)

28x10.5x3.5in short route FMIC
1g bov

BC272 cams
ARP head studs

10gage Rewired 255hp fuel pump
SS filter to rail fuel lines
SS rail to FPR fuel lines
Aeromotive 13109 AFPR
Marchell liquid filled FPG
RC 550cc injectors

relocated battery to rear

150psi Meth injection
m7 injector & LED indicator
rear 1 gallon tank with LED float and inline filter
ignition on/off toggle

Megan Short shifer
Energy suspension shiter bushings
Underhood shifter bearings

Shaved and pollished valve cover
JMfab pollished heatsheild
Pollished Injen Fuse box
Pollished catchcan
Pollished oil cap
Red vacuume lines
Red wire loom
Emissions Elimated

Some old Photos...

http://i18.photobucket.com/albums/b122/scottsee/96%20gsx/100_3068.jpg
http://i18.photobucket.com/albums/b122/scottsee/96%20gsx/100_3423.jpg
http://i18.photobucket.com/albums/b122/scottsee/96%20gsx/100_0132.jpg
http://i18.photobucket.com/albums/b122/scottsee/96%20gsx/f1abb4fd.jpg

[droppinbottom]

Nice scott. Lets see some more close up pics of the engine bay. Now I need to do some clean up work under the hood.

What setup did you go with on your meth?

[BOOGEYMAN]

Thats a very nice car!!!!

Travis

[Silver R/T]

nice setup

[The Hog]

Very clean ride, I dig it. So clean its worth putting an exra "L" in the word polished 3 times hehe

[NIevo]

Looking good! So what are your plans/goals this year?

[96gsx]

Very clean ride, I dig it. So clean its worth putting an exra "L" in the word polished 3 times hehe

LOL, I suck at spelling.**I'm supprised thats all I didn't spell right..

My "wish" is to break the 2g/evo316g record this year.**11.745 by Ken O'Conell in 2005.**But I'd settle an 11.99.** Last year I hit my 12.422 the first time out on the evo316g, and never went back.**With these new Brian Crower 272 cams, Race gas, 25psi, 22deg timing advance and a little luck I'll do it.....

[NIevo]

How are your 60' times?

[rrussell]

Man that is one clean 2nd gen. Major props!

[96gsx]

http://i18.photobucket.com/albums/b122/scottsee/mic/timeslip.jpg

Not bad on stock tires/suspension/clutch/tranny/7bolt

Here is the log file to that run, there is a bit of improvment to be had..
http://www.dsmlink.com/forums/attachment.php?attachmentid=7234

Qick overview

21psi
pumpgas
50/50 h20/meth mix
stock cams
0-60mph in 4.5 seconds
11.7-11.5 AFR
220F deg coolant temps!!
15deg timing advance in 1st,2nd,3rd
12deg timing advance in 4th
35lb/min airflow

[NIevo]

Not bad, but some improvement would go along way toward those 11's! When are you planning on doing the clutch, and have you thought about some DR's?

[GetawayInMoscow]

If you could get that 60' down that would help a lot

[96gsx]

Those 0-60 foot times are about as good as it's going to get with my stock clutch.**I'd use drag radials if I could find a good used set for $200, but I've never really seriously thought about it.**My largest gains are going to come from these BC272's, NLTS, racegas & better timing advance.