PDA

View Full Version : Camaro Dyno Results! Whoo Hooo!

Turbo_Z
09-12-2006, 08:26 PM
So I finally took my hunk of junk to the dyno. Heres the combo first:

Stock 350 block from junkyard 60 over, I just honed it a little
Stock rods
Trw -15cc forged dish pistons
Arp studs/bolts throughout
2.02/1.60 stock iron heads, no porting
stock mystery cam from junkyard
Torker I single plane intake
holley 750cfm carb
Stock HEI dist locker at 24 degrees
Walbro 255lph fuel pump w 1/2 inch lines
MP T-70 turbo
BIG Ford Powerstroke intercooler

All runs done with 92 octane pump gas and timing locked at 24 degrees.

9 psi boost
Max HP: 389 hp 4700 rpm
Max TQ: 472 ft/lb 4300 rpm


14 psi boost
Max HP: 492 hp 4600 rpm
Max TQ: 563 ft/lb 4500 rpm

I have never been to dyno before, and I have to say it was pretty cool!
KryptoSol
09-12-2006, 08:35 PM
nice job! where'd you dyno at?
Turbo_Z
09-12-2006, 08:36 PM
I dynoed at PTR Injection. They have a pretty decent setup there, and it is really close.
sefus
09-12-2006, 08:48 PM
Congrats buddy! I cant believe how efficient that turbo is after 12 pounds. Glad I could be there!
The Hog
09-12-2006, 09:00 PM
Very nice work Billy.
rrussell
09-12-2006, 09:31 PM
:cool:Way Cool!!!!!!!!!!!!!!!!!
il_wolf_li
09-12-2006, 10:57 PM
Damn Billy!!!! Big congrats on making some damn good power, now ya need to get it out to the track and see what it will run!! What kind of tires are you running....gonna have a set of slicks or anything to hook that power?
Turbo_Z
09-13-2006, 12:00 AM
Damn Billy!!!! Big congrats on making some damn good power, now ya need to get it out to the track and see what it will run!! What kind of tires are you running....gonna have a set of slicks or anything to hook that power?


I have my 275/15/r15 bgf radials on it now. I dont know if I want to put it all to the ground with this rearend. It is just a stock posi '92 firebird rearend( 7 5/8 in. I think). I might have to iceskate my way down the track with these radials.
Greycobra_03
09-13-2006, 02:03 AM
Nice!
94blueGSX
09-13-2006, 08:45 AM
Very nice. really takes off at the higher boost levels. congrats.
ntrcptr90
09-13-2006, 03:47 PM
Glad to see some good numbers from that turbo. Interesting that your using the walbro pump, is that the intank one?
Turbo_Z
09-13-2006, 04:26 PM
Glad to see some good numbers from that turbo. Interesting that your using the walbro pump, is that the intank one?


No, it is the inline pump.
sefus
09-13-2006, 08:43 PM
The Lego Land Camaro vs the Junk Yard Dog... that would have been interesting.
GetawayInMoscow
09-14-2006, 08:47 PM
god damn thats a lot of torque
ntrcptr90
09-14-2006, 09:52 PM
The Lego Land Camaro vs the Junk Yard Dog... that would have been interesting.

Well if billy doesn't sell the camaro, we can do it next year.
Turbo_Z
09-14-2006, 11:21 PM
god damn thats a lot of torque


Yeah, but it's a little shy of trbo355'(marty's TT trans am) torque. He has 692 ft/lbs!!!!!, on stock internals!!! Now that is a lot of torques.
ntrcptr90
09-15-2006, 07:01 AM
god damn thats a lot of torque


Yeah, but it's a little shy of trbo355'(marty's TT trans am) torque. He has 692 ft/lbs!!!!!, on stock internals!!! Now that is a lot of torques.

But he also has twins, when mike dyoed my kit with one dead cylinder he put down 420rwhp/575tq. You actually have quite a bit of torque for a single.
badassmav
10-05-2006, 07:56 PM
What kind of dyno does Kirk have up there??
KryptoSol
10-06-2006, 10:03 AM
What kind of dyno does Kirk have up there??


DynoCom, its supposed to be a copy of the DynoJet.