BOOGEYMAN
12-21-2008, 05:49 PM
Hey everyone! I havent been one here for a long time but been busy around the house and with the newest project! Couple months ago I bought a 19ft Eliminator Daytona jet boat from Tony Skagen at Skagen Boats Established 1969 (http://www.skagenboats.com) This was his personal boat he built.
It is a medium weight lake/race set up, here are a few spec's.
Custom TSR race pump (Tony Skagen Racing)
Low profile intake with an mpd loader trimed by Tony
4340 race shaft
9.5 stainless steel, high helix AAAA impeller
Custom agressor bowl to accept the high helix impeller
Straight snoot
Adjustable nossile by place diverter
Ride plate and custom shoe by Tony
Everthing is double drilled and studed
I traded my mustang for Noahs long block built by Cassle performance
496 BBC
Eagle rods with the L19 bolts
Eagle 4340 crankshaft
Srp pistons
Solid roller set up
Canfeild aluminum heads ( wich will be recieving inconal exhaust valves)
Dart single plain intake
Single C&S Dual needle and seat blow thru carb with the pro series hat.
Twin BW s475's with T6 1.10 housings
Twin 60mm wastegates
Single 50mm BOV
Should make around 1,000 or so on pump gas and figure I can squese a nice 1,150-1200 out of that stock block on a nice tune up. Going to run this next season with this set up then most likly set up to bigger cubes, a dart block with a better internals and really turn the boost up!
I built the headers myself but had them mocked up for my sleekcraft jet boat but sold it so I need to rework them a little bit to make them right for the eliminator. Marty at Stromberger's performance will be doing the finish tig weld's on the headers and the cold side. This will be an air to water IC set up as well. I will also be adding a back seat almost a duplicate to the front! I will post pic's as progress continues.
Here are a few pic's, some with the blown 598 BBC that was in it, the pump, and some of the new engine in mock up. The intake and carb in there pic's are just for mock up purposes.
Thanks for looking!
Travis
It is a medium weight lake/race set up, here are a few spec's.
Custom TSR race pump (Tony Skagen Racing)
Low profile intake with an mpd loader trimed by Tony
4340 race shaft
9.5 stainless steel, high helix AAAA impeller
Custom agressor bowl to accept the high helix impeller
Straight snoot
Adjustable nossile by place diverter
Ride plate and custom shoe by Tony
Everthing is double drilled and studed
I traded my mustang for Noahs long block built by Cassle performance
496 BBC
Eagle rods with the L19 bolts
Eagle 4340 crankshaft
Srp pistons
Solid roller set up
Canfeild aluminum heads ( wich will be recieving inconal exhaust valves)
Dart single plain intake
Single C&S Dual needle and seat blow thru carb with the pro series hat.
Twin BW s475's with T6 1.10 housings
Twin 60mm wastegates
Single 50mm BOV
Should make around 1,000 or so on pump gas and figure I can squese a nice 1,150-1200 out of that stock block on a nice tune up. Going to run this next season with this set up then most likly set up to bigger cubes, a dart block with a better internals and really turn the boost up!
I built the headers myself but had them mocked up for my sleekcraft jet boat but sold it so I need to rework them a little bit to make them right for the eliminator. Marty at Stromberger's performance will be doing the finish tig weld's on the headers and the cold side. This will be an air to water IC set up as well. I will also be adding a back seat almost a duplicate to the front! I will post pic's as progress continues.
Here are a few pic's, some with the blown 598 BBC that was in it, the pump, and some of the new engine in mock up. The intake and carb in there pic's are just for mock up purposes.
Thanks for looking!
Travis