Tall deck 498 BBC FOR SALE

[2UPONU]

Gauging interest. Looking at buying a car and I don't need the engine, tranny or converter.


New, not run 498 BBC tall deck, block is filled up to the bottom of the water pump jacket. This crank a Callis dragon slayer crank (double keyed) BME aluminum rods and 14.1 wiesco pistons. Milodon dragster flat pan, iski roller cam and lifters. Merlin steel heads, 345 runners, 119CC chambers. triple springs with 325 seat pressure. The block has been o-ringed and the heads have receiver grooves. This engine was built for a super charger to be run on Methanol.. With the .80 copper gasket it brings the compression down to 12.1 so its safe to run that way.. (can not be run with super charger and gas) There would be no problem putting on a manifold and domintator if you wanted to.. This lower end was built to hold 2,500 HP... With the 8-71 and 16 pounds of boost I was looking to make about 1,800 HP.. With a 1150 dominator and good manifold it should make an easy 1,100 HP.. (also a mezere billit flywheel)

$7500, or make offer!

[gregc]

Killer deal on that combo for anyone looking.

[2UPONU]

more info....It is a 1967 Chevy tall deck block.. It is filled up to the bottom the water pump holes.. Everything in the engine is BRAND new. Callies Dragon slayerer crank shaft.. (double 1/4 key's) BME aluminum rods, Wisco pistons.. The heads are Merlin steel heads,. 345 runner 119cc chambers.. Everything in the engine is BRAND NEW.. The heads are used but just done. push rods new.. rockers new. stud girdles new..crank hub is new.. there is a degree ring on the hub. that is new.. Gear drive is new, cam is an ISKY cam that is new..

[2UPONU]

Don't make me part this out!

[Ninja_Bear]

Perfect swap for my '89 S-10...

[2UPONU]

Still available. So is delivery...

[2UPONU]

bumpy bumpy

[2UPONU]

Parting out. Lots of good parts, email for list and prices

[2UPONU]

**1967 tall deck 427 truck block, 4.310" bore, o-ringed, four bolt ARP studded mains, filled to bottom of water pump holes $1000

**Merlin "Grumpy Jenkins" #1-043, freshly rebuilt, 119cc chambers, 345 CFM steel heads. Titanium retainers/locks $1200

**Wiseco pistons and rings. Piston #6320A6 1.520 compression height, .700" dome, .990" pin $650

** BME aluminum rods, 6.385 length $900

**GM forged 4.250 crank .010/.020" double keyed, crankk done by Hank the Crank $800

**Isky solid roller cam 114, .799/.765 @ 1.7 rocker, .288/300 @ .050" $325

**Dedenbear Water header $75

**Enderle front cover/and pump drive $95

**Milodon dragster pan/pump/pickup/driveshaft $390

**Isky solid roller lifters $350

**8.850/9.800 3/8 pushrods $100

**Crane Gold Race 1.7 roller rockers $220

**Dart #454 stud girdle and polylocks $250

**Pete Jackson gear drive $150

** 7/16 ARP head studs $125

**two sets of sheetmetal valvecovers one set clearenced for injectors $50 each

**.080" copper head gaskets $100

Heads are off engine. Shortblock is assembled, never fired. All parts are new with the exception of the heads crank and block which are fresh.

All prices are OBO. Contact Ken 406-370-0574 for questions or more info.

[Northwest outlaw]

i was looking at the rods but to small. I need 6.7

[2UPONU]

I have a set of GRP rods that are 6.665". Very little use.

[Northwest outlaw]

Ill see if it will work with my pistons i think it will put to far down in the hole ill get back to you on it.

[Northwest outlaw]

my motor guy said that to short for my build with the block deck ,head gasket and the short rod is not going to put us where we want to be. sorry

[2UPONU]

No prob. Thanks for checking.

[jerpolson]

I was curious if the 427 Tall Deck Block was still available? And if so, whats its condition and can you ship it?

[Northwest outlaw]

Old post some one mite have his number to see if he still has it.

[2UPONU]

I was curious if the 427 Tall Deck Block was still available? And if so, whats its condition and can you ship it?


I still have it. Excellent condition. Where are you located? I am in Missoula, MT shipping shouldn't be a problem depending on where you are. The rotating assembly is still in it. Do you just need the block??

You can also try my cell 406.370.0574

Ken